90 Degree Fuel Line Fitting

C5 Fuel Filter Replacement - Corvette Legends
Special Tool Required: (5/16") fuel-line disconnect tool Relieve the pressure in the fuel line at the rail. Remove the plastic cover from the driver’s side of the engine. ... Document Retrieval

UL Power UL350 Series Engine Installation - Section 4 - Fuel ...
UL Power UL350 series Section 4, Page 1 of 16 Install the 90 degree Swivel on the Fuel Pump Ramp. P/N: F3008090 90 degree Swivel Install the 90 degree Swivel on the end of the Braided Fuel line. Thread the Swivel on the fitting on the Injector Holder on the passenger side of the Engine ... Access Document

Forged Steel FittingS & UnionS - Bonney Forge®
2 Bonney Forge - The Company You Rely on For Forged Steel Fittings and Unions Since 1967, one name has been syn-onymous with premier Forged Steel ... Read Full Source

FUEL SYSTEM PARTS - MikesXS
FUEL SYSTEM PARTS MANUAL PETCOCK TO REPLACE VACUUM Petcock 90 degree outlet fitting Replacement fittings - Fits:XS 650 Petcocks #20-0019/0050/0051 BRASS FUEL LINE T T-Piece - ( Fuel supply T pipe that fits between carbs ) ... Fetch Document

Sheet Metal - Wikipedia
Deep drawing is used for making automotive fuel tanks, Here, the die has a sharper angle than the required bend (typically 85 degrees for a 90 degree bend) and the upper tool is precisely controlled in its stroke to push the metal down the required amount to bend it through 90 degrees ... Read Article

Hydraulic Hose & Fittings - Royal Brass And Hose
TABLE OF CONTENTS To order by phone:1-800-669-9650 To order by fax:1-800-736-0141 6 ITEM PAGE # ... Read Content

69252G Fuel Tank Vent - Attwood Marine Products
FEATURES: The Attwood water-resistant 90° fuel tank vent is designed for permanently-installed fuel systems and is intended for use with 5/8" vent hose. ... Access Doc

Fittings - Bergstrom Inc
295 2 A/C Fittings Fittings (800) 499 -6849 • www .kysorhvac .com Beadlock O-Ring R-12 service Port V Indicates Aluminum fitting Beadlock O-Ring 90° Female O-Ring w/R-12 Port Fitting size thread size Hose size Hose i .D . ... Fetch Content

14360A78 FUEL PUMP REPLACEMENT KIT FUEL PUMP ... - Marine Engine
FUEL PUMP REPLACEMENT KIT WARNING Use caution when changing fuel pump; gasoline is extremely flammable and highly e-Fuel Line Connector f-Molded Hose g-Fuel Pump h-90 Degree Elbow i-Fuel Outlet to Filter j-Hose [2.5 in. (63.5mm)] k-To Pulse Fitting on Powerhead Model 100, 115 ... Visit Document

How To Make A Fuel Line: FMSI - YouTube
Demonstration and instructions on how to create a fuel line easily with 45 degree quick connector. Kit used was 0454M (kit contents at end of video) www.fmsi ... View Video

Quick Reference Product Guide - Coastal Hydraulics
Brennan Industries, Inc.’s hydraulic tube fitting and adapter part numbers are constructed from symbols that identify the series, size, material and type of product. When ordering part numbers, begin by listing the series followed by the size and the material suffix. ... Retrieve Document

Start With An Empty fuel Tank. - East Coast Supercharging ...
Factory fuel feed line as shown below. With a second length of 24 in 8 AN hose, we will assemble the line from the ECS auxiliary fuel block to the Pump inlet using a 120 degree fitting on either end. ... Read Document

Gas Risers And Transition Fittings - Elster Perfection
The first gas service line riser is still the best for providing utilities a safer and more economical means of distributing natural gas. 1 Servi-Sert Fitting 2 Prebent or Flexible Casing 1 2 Single or double seal riser Flexible riser. ... Document Retrieval

6 With the fuel selector in OFF, the fuel line was removed from the carburetor. A 90 degree fitting of the same size as the fuel lines (3/8 inch) was attached to the fuel line to ... Retrieve Document

Eaton Aeroquip TTC Series Fittings
4 EATON Aeroquip TTC Series Fittings A-HOOV-TP001-E2 July 2012 New MatchMate Part MatchMate™ TTC Series Fittings TTC Hose Hose Cut-Off Part # Thd. Size A Factor (D) EØ mm in mm in mm in in ... Access Doc

2 2011-2014 6.7L Ford Power Stroke Dual High Pressure Fuel Kit
8 2011-2014 6.7L Ford Power Stroke Dual High Pressure Fuel Kit www.hs-motorsports.com 9 Install a 3/8 straight and a 90 degree pushlock fitting onto fuel feed and return fittings. Route conversion kit while the 90 degree line will be connecting to the 3/8 barb on the Fuel “T”. ... Visit Document

HOSE FITTINGS - Highgate Car Air
MOULDED HOSE WITH 90 deg. BEND 13 mm DIA. - 400 mm LONG MODEL - CODE - ENGINE HOSE / LINE TYPE REF. YEAR PART No. OEM REFERENCE. 290 HOSE and HOSE FITTINGS Highgate Automotive Air Conditioning Catalogue C BARB FITTING Hose Fittings. ... Retrieve Document

Technical TECHNICAL - Parker Hannifin
** Maximum service pressure for lube oil and fuel systems applications (Code F) may be less than maximum service pressure for other systems applications, e.g., Code H. Refer to individual hose listings in Section A and Hose Assemblies List, SAE J1942-1 or HPD Approval Bulletin #APR-004. ... Get Doc

Section Pages - Eaton
Versil•Flare™ Tube Fitting Connection …188 NOTE: Due to the infinite number of adapter combinations, materials and finishes available, Eaton Aeroquip does not catalog all items it stocks or has the capability to manufacture. ... Fetch Full Source